I am working on porting WinCE 5.0 onto a XScale system with an embedded
PCI, on which TI1520 and VIA USB host sit. TI1520 is designed to
support PCMCIA and CF cards. These two cards or functions shared the
same interrupt pin. In addition, the USB host drives two UHCI and an

I am working on Touch Screen driver ,working on PDD layer.
I was refering to Sample codes ...
DdsiTouchPanelGePoint() , in this  function timres are used ..why ..? If i
have a function in my core library which rerurns raw values of X,Y along with

If I build an executable using Platform Builder 5.0 the OS Version is set to
4.0 and the Subsystem vsersion is set to 5.0 in the program header. This
means that it will not run on previous versions of CE. If there any way to
over-ride this?

I have a problem that I can only connect to the internet when KITL is
active.
I found out that connmc.exe is started when I have KITL activated.
This seems to be part of Net UI which I have also included now into

I want to read SD/SDIO/MMC cards on our board which has a PXA255
processor. Needless to say our SD slot is connected to its MMC
controller. At a first stage, I would be happy to read MMC memory
cards.

I'm developing code for an Arm4 processor. It appears that the lasted
supported CE version for this is 4.2. Can anyone tell please tell me where I
can get a copy of Platform Builder 4.2?
Thanks in advance

Dear Experts,
At present We are developing WindowCE5.0 Ethernet driver for Atmel At9
processor. We referred the SMSC100FD driver code as a reference drive
given in

  I have tons of queries on writing a USB Flash drivers on Windows CE 5.0
(or .Net)  for my school project. At this point of time, I couldn't decide
if I should get a Pocket PC (Windows Mobile) or a development board. Which
is more "doable" in a reasonable timeframe (for a ...

I am in process of Using NE2000 Netowrk cards and 802.11 wireless
CFlash cards with WinCE 5.0 for a ARM processor .
With my registry Settings i enable DHCP
[HKEY_LOCAL_MACHINE\Comm\NE20001\Parms\TcpIp]

I am getting a data abort on the folowing bit of code
memcpy(pTargetBuffer, (BYTE*)pI2C_regs->IDBR,sizeof(BYTE));
pTargetBuffer is PUCHAR, IDBR is a DWORD, basically i'm copying my
I2C receive data into read buffer. I know ican do another way but want to know why

Dear Experts,
At present We are developing WindowCE5.0 Ethernet
driver for Atmel At91 processor. We referred the SMSC100FD driver code as
a reference driver given in the

Uninstalling PB 5.0 does not remove the Device Names (discovered via
the BOOTME process) nor the Target Connectivity Options settings for
these Target Devices.
I would like to remove these values so that I can start out with a

I'm new to ActiveSync and I'm trying to get it working over a serial port.  I'm using CE 5.0 and I believe that I have all of the QFE's installed.  I'm using the Cirrus EDB9307 eval board and the cable that they provided with the board for just this purpose.  My image was build ...

Sincerely appreciate if anyone can shed light on a problem that I have
with PB 5.0 Target Connectivity: Kernel Debugger (host-side KDBG
Service) attach fails for Mainstone III target, Ethernet KITL transport
but works for a generic CEPC target!

I am trying to run the System Information tool from PB but am getting a
dialog asking for the location of the file ntirp.c. I can not find that
file anywhere and don't find any references to it on MS's site. If I
cancel the dialog I get an error that 4 devices were retrieved but ...