Isnt the bluetooth stack supplied with the WinCE installation, SIG
qualified? As per the BT SIG site, the profiles qualified in WinCE 4.2
stack are GAP,SPP, DUN,FTP,LAN,OPP,GOEP etc. But the source in WinCE
4.2 installation has only profiles DUN,LAN,OPP,FTP.Same is the case

We are developing a board based on the Mainstone II BSP, and I am trying to
get the serial ports to work. (this part of the board is identical to the
Mainstone, in fact its pretty generic to the PXA270). I can transmit out of
the port OK but cannot detect characters coming in. I ...

Iam working in a hardware kit which has PXA 270 processor. I couldnot
download the image(NK.BIN) to the RAM of the hardware kit. Iam getting
a debug message as "TAPI NOT READY". A closer look through the
platform's release directory caused me to know that the EBOOT.bin files

After adding the AYGShell Extension the SIP pops up every time I select an
edit box. Futhermore it also pops up If I deactivate the "Allow applications
to change the input panel state" in the control panel applet "Input Panel
Properties".

Hi,
I have custom PXA255 platform based on Lubbock
BSP. I have a problem with resume in that when i do a
suspend from the Start button the system powers off

We have a need to develop a WInCE 5.0 bootloader that could boot the WinCE
image over USB interface. The platform is based on PXA 270 processor. The
boot process should be similar to  Eboot that happens over Ethernet. Few
questions I have :

   am in PB 42.net and the device is arm9.
   Now the bsp using one of the SOC PWM timer as the scheduler timer.
   Only in the  OEMInterruptHandler(), if the interrupt is the PWM's timer,
the Led is turn on or turn off.

i use platbuilder5.0 +SMDK2410 ,and i want to write a ExtInt0 interrupt
server,but when i push Extinto button,always show error c0005,why?
please tell me ! help !!!
void int0_init(void)

i've been doing a lot of networking programming on win desktop but would
like to dive into win ce NDIS development. what's a good starting point
(tutorials, books, web sites) ..
best regards.

On occasion I get a failed attempt to associate with a "preferred" access
point.  If I then use zero config and hit the "Connect" button to force
another attempt it will connect right away.  Also, if I just leave the
system, after a while a second (or subsequent) attempt to ...

Do the stream driver XXX_PowerUp and XXX_PowerDown
functions need implementing. Is it enough to have stubs. I am under
the impression that the IOCTL_POWER_XXX codes need
implementing and thats enough. If so when are the XXX_powerUP

Pls let me know how I can view UART interrupts arriving on the COM port.
I wanted to know whether an interrupt is generated on the arrival of data on
the COM port? If so, what is the interrupt generated? Can I view this
interrupt by writing a small application?

I want to interface a host controller FPGA with the  PXA270 processor
in my hardware kit. My hardware kit has PXA270 processor and Host
controller  of its own. I want to know about the registry key values
used to load a host dll. GIven below is the part of the registry taken

I am using touch screen to wake up from IDLE mode, it is waking up
correctly but also activating any aplication or ICON present in that
area. Does anyone know how to avoid this problem, any hints or advise
will be appreciated. Thanks

I've got a problem I haven't been able to figure out.  The problem occurs
when trying to boot the image from CF.  The CF is connected to an IDE port.
Here are the steps I used:
1.  Built a debug image