I am trying to connect to my host PC (winXP) with active sync to a WinCE6 OS.
I have tried this on 3 PCs all have usb2.0 conectivity, however only 1 of
these PCs can achieve a USB2.0 conection, the other 2 are USB1.1. All PCs are
recent, None started with anything less than SP2 of ...

the usual wait for bootme, pick the target device name, apply, close.
try to download a os, pb prompt a error. go back and check setting, device
name is gone.
I have to leave the connectivity options window open in order to finish the

In order to build a new version of an OS design, I use the following procedure:
- copy of the entire workspace in a new directory
- manually update the Workspace PlatformName in the .pbxml file
- make the necessary changes in the new OS design.

I have an on-board 16Mbyte StrataFlash and would like to use the low 8MByte
for XIP and the upper 8Mbyte for Flash disk.
Is it possible to use the same flash for XIP and flash disk at the same time?
/trond

Platform builder has many default pltforms. For ARM,
all are based on ARMv4 architecture. Our target platform will use ARM cortex
A-8 based on ARM v7 architecture. Does Platform builder support the advanced
features like the Thumb2 instructions of ARM cortex(ARMv7) and its ...

Hi, I am developing a embedded platfrom using Windows Embedded CE 6.0 but
I have a problem about USB function driver.
The target board print following debug messages when connect USB client port
of the board to USB host port of host PC with USB cable.

I have installed Embedded CE 6.0 R2 and the first thing i do after this
intstallation is an Update Check. After the check i found that no-one update
has been installed on my CE enviroment. Obliovsly i have installed all the
update before R2.

Hey guys,
I am using DaVInci DM6446 DVEVM board and WinCE 5.0
I have created a workspace with Catalog items added, provided both by
Mistral BSP and default WinCE drivers.

I heard that WinCE 6.0 comes with KITL over USB. In fact i have WinCE 6.0
installed and i can see the option in the "Connectivity Options" menu. My
question is, with the case of the DOS utility, "loadcepc"... how do i get it
to connect to my host machine via USB for download?

I'm integrating Cs8900 ethernet controller on my i.mx31 target board.
I'm using a debug version of the image. At the boot the ndis.dll has a
prefetch abort lister here below and of course the ethernet interface is not
working.

Hey all,
I am writing a sample application for Bluetooth Service Discovery process
using WinCE APIs using Platform Builder.
The steps that I have followed are as follows:

 I am using windows ce 5.0, and I have two ce devices, one has a usb host
and ther other is a usb rndis function device. the rndis function device has
been tested on a xp and have no problem.
but when i connect the function device to the wince usb host device, ce host

I was trying to build "L2CapDev.dll". The source code is located in:
  %WINCE600%\PUBLIC\COMMON\OAK\DRIVERS\BLUETOOTH\SAMPLE\L2CAPDEV
When I started to build, I encountered the unresolved symbols at
linking stage.

I'm having the atapi driver which is working well than the 4.2 driver. So i
just put that 5.0 driver in 4.2 workspace and gave makeimage. It gives error.
Whether 5.0 driver does not support backward compatibity. Similar things also
happened, when i tried to use 6.0 atapi driver ...

I copied a Platform Builder 5 workspace from one computer to another,
and on the new computer the resulting BSP size approximation is always
0.
I can't figure out how to get it to display an approximation again. Is