Having read the MSDN CETK info on this item, I have found that some of the
pre-requisites are not available, specifically USBPERF.DLL
I have not found a project that builds this item in either WINCE600 or 500,
I have also not been able to locate a USBPERF.DLL binary.

Could someone please provide me with the download location for the
USBPERF.DLL or instructions on how to run the test with the existing USBTEST
project?
I need to benchmark the max throughput of the USB Host Controller at the bus

When I go to install the Test Kit, I get the following error message:
"This installation package could not be opened.  Verify that the package
exists and that you can access it, or contact the application vendor to
verify that this is a valid Windows Installer package."

I am testing the test case 112 of OAL Timer, but it always fails,
The OAL Timer was implemeted using variable tick,
Who can tell me if the variable tick will effect the test case 112 of OAL
Timer?

As per prerequisties for this USB Host controller driver test its specified
that we require a CEPC with
NetChip 2280 USB Host controller card.
Is this card same as a inbuilt USB in the PC ?

These day's I am looking some way to test a USB CDC Driver for Windows
CE. The problem is I cannot use Windows TK (Test Kit) since there I
need to write another code for the TUX.dll to perform the test. If
someone can help me to sort out this problem, it would be very much

  When I tested Direct3D Mobile Driver Comparison Test item, it was failed
and the failed message was like this:
*** vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
  D3DMQA: ShellProc(SPM_BEGIN_TEST, ...) called

Hello,
    I have met some questions when do CETK GDI performance test on WinCE
5.0. I found the test result always display "Failed" on Windows CE Test Kit
UI, but I can't find any information about why the test failed excepted

I am running GDI test from test kit in a device with little memory and I get
this message in test:
      System Info: Storage in use is 1978368
      System Info: After increasing: dwStorePage=727  dwRamPages=3206

I use COM1 to receive test info data when I am running test. I use the
software Accessport.exe. So I think my COM port is all right.But yht log
shows error55 means ERROR_DEV_NOT_EXIT.I use the default command line tux –o
–d serdrvbvt .

I am trying to invoke the Application Verifier for Mobile 5.0 but am getting
an "Unable to enable shim engine on device" error.  This happens when trying
to connect to an WM 5.0 emulator or a WM 5.0 physical device.  
I can successfully connect CETK via ActiveSync in both cases ...

I am receiving the following test case failure when running the DirectDraw
CETK test suite:
<TESTCASE ID=100>
*** vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv

I'm having trouble getting the command line parameters for this test to work
as described in the documentation. Please can you help?  Here are my
questions.
1) The -v parameter did not change the verbosity of the status info when I

In this newsgroup, I've seen a number of people asking about documentation
for the USB Host Controller CETK tests (usbtest.dll), and a few promises, at
various times, that it would be available Real Soon Now (the latest one, in
response to a late March-2005 question, said it ...

Do any one know how to run USB CETK test cases ...
Thanx..